Recommended Tools & Gear
Over decades of building, repairing, and setting up guitars, I’ve worked with a lot of tools and products — and got burned by a fair few along the way. This page is a running list of the gear that’s earned a permanent spot in the workshop at Guitar Assembly. The things I actually reach for, not just what looks good in a product photo.
I’ll be adding to this as new things prove themselves. If you have questions about any of it, get in touch.
— Martin
Glues & Adhesives
Franklin Titebond Aliphatic Glue
The best wood glue for almost all aspects of guitar building. I use it for everything wood-to-wood at Guitar Assembly — bridges, fretboards, body blanks, and crack repairs. When it sets, it’s often stronger than the wood itself. It cleans up with water before it cures, sands easily once dry, and doesn’t absorb stains, so any squeeze-out can be sanded away cleanly.
Works between 10°C and 43°C, so don’t use it in a cold garage in winter.
Hide Glue
I use hide glue rarely — primarily when working on vintage instruments where it was originally used. Titebond also makes a liquid hide glue that speeds things up considerably if you want to explore it without investing in a full heating pot setup. Luthier’s Mercantile fish glue is a viable alternative if you need the reversibility of hide glue without the hassle of preparation.
For most builds and repairs, Titebond is the one.
Cyanoacrylate (Superglue)
Not for joints or body blanks — this is the glue for small components. Fretboard inlays, tight cracks that need penetrating, and places where a thin viscosity really helps. It dries clear and hard and sands just as well as aliphatic glue.
Brand matters less here than with Titebond, because you use so little of it. Loctite, Gorilla, Krazy Glue — any decent industrial-grade CA glue will do the job. Just keep the working area ventilated; the fumes are no joke.
Epoxy Resin
Used for filling dents, chips, and small cracks on fretboards — things you’ll sand flush later. I use it with a hardener, and the ratio matters; get it wrong and you either get something that won’t cure or something that sets before you’re ready. West System is the brand I reference most.
Good in situations where you need a hard filler. Not a substitute for Titebond in structural joints.
Strings
Rotosound
My string of choice, and has been for years. The main reason I keep buying Rotosound is practical: they include a spare high E string in the pack, which is the string most likely to go on you mid-restring. I’ve got quite the collection of spares built up at this point, but it’s the kind of thing you appreciate when you need it at 11pm before a session.
They’re made in the UK, they’re consistent, and they sound good. What more do you need?
Ernie Ball Slinky’s & D’Addario XLs
Both are solid alternatives that plenty of serious players swear by. If you’ve got a preference for either, keep using them — there’s nothing wrong with either brand. They’re mentioned here because they come up when students ask about alternatives to Rotosound. Ultimately, pick what you like and play it.
Fretwork Tools
These are the specialist tools. Some are available on Amazon, but a good number are from StewMac — which is the go-to supplier for luthier tools worldwide.
Fret Saw
A good fret saw is essential if you’re cutting your own fret slots. I use the Japanese-style fret saw from StewMac. The kerf is precise and consistent, which matters a great deal when you’re cutting slots for specific fret wire gauges.
Fret Press
For pressing frets in cleanly and evenly. The StewMac Fret Press is the industry standard. Paired with the right caul for your radius, it dramatically reduces the amount of work you do after the fact to level and dress the frets.
Fret Cutters & Nippers
I use the StewMac Fret Cutter and Knipex End Cutter in the workshop. The StewMac cutter is purpose-built for fret wire and leaves a clean, close cut. The Knipex is a general-purpose nipping plier that’s a solid alternative if you’re just starting out and don’t want to invest in the full StewMac setup right away.
For pulling frets, both Northwest Guitars and StewMac make fret-pulling pliers. The StewMac ones are excellent. Knipex nipping pliers also work for removal with care.
Fret Hammer
Brass, nylon, or rubber — any of these works for seating frets when you’re using a hammer rather than a press. The choice mainly comes down to personal preference and what type of fret wire you’re working with. It’s not a complicated tool; just make sure it’s the right weight for the job, and you won’t dent the fret crown.
Radius Blocks
Essential for levelling fretboards and fret wire to the correct radius. Available on Amazon and from various luthier suppliers. Just get the right radius for the neck you’re working on.
Fret Bending Jig
If you’re installing frets, you need to pre-bend the fret wire to match your fretboard radius. You can build a simple jig yourself, or pick up a cheap one on Amazon. Nothing complicated — it just saves you fighting the fret wire during installation.
Soldering Iron
Useful for heating frets during removal, which makes the process significantly cleaner and reduces the risk of tearing up the fretboard. Any decent temperature-controlled soldering iron works. Not strictly a fret tool, but it earns its place in this section.
Fret Polishing & Care
MusicNomad FRINE Fret Polishing Kit
This is what I use in the workshop for routine fret polishing. The kit comes with everything you need: fret guards in three sizes (to suit different fret wire widths), FRINE polish, and a microfibre suede cloth. You apply a small amount of polish to the cloth, slide the fret guard over the fret to protect the fretboard, rub the fret, and wipe it clean. Repeat 22 times.
The fret guards are what really make this work quickly. Without them, you’re either taping the fretboard (which takes forever) or getting polish everywhere. The FRINE formula is petroleum-free, which means it’s safer around fretboard woods and finishes.
MusicNomad FRINE Kit on Amazon →
StewMac Fret Erasers
Abrasive rubber blocks for removing fine marks, burrs, and scratches from fret wire. Come in a range of grits. Useful for more involved fret work when you need to remove actual material rather than just polish.
Emery Paper & Emery Cloth
We always have both in the workshop. Emery paper for flat surfaces, emery cloth when you need flexibility — around bridge slots, tuning shaft holes, anywhere geometry makes rigid paper awkward. For metalwork on the guitar (saddles, tuning posts, nut slots), ultra-fine emery at 2000 grit is the go-to.
Available anywhere that sells sandpaper. Nothing brand-specific to recommend here.
Fretboard Conditioning
A note upfront: you need far less oil than most people think. Once or twice a year on an unfinished rosewood or ebony fretboard. Never on maple (maple fretboards are sealed and don’t need conditioning). If you’re unsure, do less.
MusicNomad F-ONE Fretboard Conditioner
A favourite in the workshop. F-ONE is a clean, well-formulated conditioner — free of lemon oil extracts, waxes, petroleum distillates, silicone, and water. It cleans and conditions in one step without leaving the fretboard sticky or over-oiled. Works well on all unfinished rosewood fretboards.
Boiled Linseed Oil
If you want one oil to put on your fretboard and never think about it again, go for boiled linseed oil. It’s tried and tested, works with any unfinished wood, and is probably what the manufacturer used when they made the guitar. Apply sparingly on a rag once or twice a year — that’s it.
Liberon BLO500 and Rustin’s Boiled Linseed Oil are both solid. The 1L Liberon is a good value and lasts a very long time, given how little you use per application.
Liberon Boiled Linseed Oil on Amazon →
Dunlop 65 Ultimate Lemon Oil & D’Addario Planet Waves Lemon Oil
Both safe options for rosewood and ebony fretboards — though neither is “lemon oil” in the pure sense. They’re mineral oils with a trace of lemon oil added, which is fine in moderation. Not for maple. Not too much. Used correctly, both are perfectly good products.
Other Conditioners Worth Knowing
- Fret Doctor Fretboard Conditioner — another solid choice, widely used and well-regarded
- Gerlitz Guitar Honey — a light mineral oil, recommended for Fender and Gibson guitars specifically
Setup & Measurement Tools
StewMac Metric String Action Gauge
The specific gauge I use and recommend. One side measures string height in millimetres, the reverse gives you a quick-reference conversion chart. It’s a simple tool, but it’s accurate and built to last.
For taking measurements at the 12th fret (where you want to be), this is all you need. Sit with the guitar in playing position, measure the low E and high E, and compare against your target height.
StewMac Feeler Gauge Set
Useful for measuring string height at the nut (1st fret clearances) and truss rod relief at the 7th fret. The StewMac set covers the range you need for guitar setup work.
StewMac Fret Rocker
For diagnosing high or uneven frets, one of the most useful diagnostic tools in the shop. You place it across three frets at a time; if it rocks, one of those frets is high. Works across any three adjacent frets on the neck. There are cheaper versions on Amazon that do the same job if you’re not ready to invest in the StewMac one.
Hex Keys (Allen Keys)
You’ll need these for truss rod adjustments and bridge saddle height on most electric guitars. The sizes vary by guitar:
- Fender (American-made): 3mm or 1/8″ hex key
- Martin acoustic: 5mm hex key, often via the soundhole
Metric or imperial, depending on where your guitar was made. American guitars are imperial, European and Japanese are metric. Pick up a decent set that covers both.
Tuners
I’ve used a lot of tuners over the years. These are the ones knocking about the workshop.
Pedal Tuners
- TC Electronic PolyTune — polyphonic tuning (strum all strings at once), strobe mode for fine work, built-in buffer. Excellent all-round pedal tuner.
- Korg Pitchblack Advance — accurate and reliable, good display, a strong alternative to the PolyTune
- Boss TU-3 — the workhorse. Simple, bombproof, everywhere
TC Electronic PolyTune 3 on Amazon →
Clip-On Headstock Tuners
- TC Electronic Polytune Clip — the clip-on companion to the PolyTune pedal. Polyphonic, accurate, easy to read
- D’Addario NS Micro Tuner — tiny and discreet, good for acoustic use
- Korg PC-2 Pitchclip 2 — accurate and well-built
Apps (Free & Surprisingly Good)
- Fender Tune — clean interface, reliable chromatic and polyphonic tuning
- GuitarTuna — the other solid free option
Apps won’t replace a dedicated tuner for live use or precise intonation work, but they’re genuinely useful and much better than they used to be.
Sanding & Finishing
Mirka Sandpaper
What I use in the workshop. Available locally for us and consistently good. The brand you use matters less than the grit progression — but if you want a reference point, Mirka is what I reach for.
Grits we use for guitar body prep:
- 80 grit — initial material removal, mill marks, dents
- 120 grit — remove the 80-grit marks
- 240 / 320 grit — fine work
- 400 grit — ultra-fine finishing
Available on Amazon. Just make sure you’re using proper abrasive paper and not the cheap stuff that loads up with dust after two passes.
Sanding Blocks
Two types earn their place:
- Rigid cork block — for the large flat surfaces (top and back of the body). The rigidity is the point; a flexible block would conform to bumps you’re trying to remove.
- Flexible foam block — for contours, curved edges, anywhere the body isn’t flat. Also useful for fine finishing passes over flat areas.
For tight spots — pickup cavities, side contours — lose the block entirely and use the sandpaper on its own for more feel and control.
Emery Cloth
Already mentioned above under fret care, but worth flagging here too. Emery cloth is what we use for metalwork on the guitar — smoothing burrs on tuning posts, bridge saddles, anywhere steel or nickel meets steel. More flexible than emery paper, which matters in tight spots.
Nut Care & Lubrication
Big Bends Nut Sauce
The best nut slot lubricant we’ve used. Reduces string friction at the nut, which means better tuning stability when you’re bending strings or using a tremolo. Apply a small amount to each nut slot every time you change strings.
Kasp Microfine Graphite Powder
My go-to alternative to proprietary nut lubricant. Cheap, widely available, and effective. A small amount in each nut slot does the same job as the specialist products. Shaving a pencil directly into the slot also works in a pinch — same principle, less precision.
Nut Slot Files
For adjusting the nut slot depth. You need the right size file for each string gauge — this is a case where having the right tool for the job matters, as the wrong file will mess up the slot profile. File slowly and check often; going too deep means making a new nut.
Pickup Wire (For Those Winding Their Own)
Northwest Guitars Vintage Cloth-Covered 22 Gauge Wire
This is the wire I use in my own custom pickups at Guitar Assembly. Vintage-style cloth covering, 22 gauge. It’s found in high-quality guitars and sounds incredible — nothing like the wire you’ll find in stock OEM pickups. Available directly from Northwest Guitars.
If you’re coming to a pickup winding session at the workshop, this is what we’ll be working with.
Pickup Brands Worth Knowing
- Gibson ’57 Classic — the right choice for an Epiphone 335-style guitar
- Fralin P-92 — excellent P90-style option
- Seymour Duncan SH-55 — clean, warm humbucker
- Mudslide Guitar Custom Humbuckers — my own hand-wound pickups (naturally, our first recommendation)
- Suhr Thornbuckers — what I put in my personal Telecaster and immediately transformed the guitar
- DiMarzio DP100 / EMG 85 — high-gain applications
- Seymour Duncan Custom Shop / Bare Knuckle / The Creamery / Mojo Pickups — boutique options for when you want something built specifically to your spec
